Plumbing & HVAC Services Hicksville OH

96% efficient 70,000 btu two stage furnace and 3 stage 16 Seer 3 Ton AC

Labor for replacing draft motor

Installation of I wave

Install I-Wave

Found unit low on Freon. Put 1lb of r410a in. Verified proper operation. Unit has 18 degree now 59 and 77 degrees. Was 11 degrees upon arrival.

Thermostat was giving an alarm for condensate overflow. Inspected drain, trap, and condensate pan. All were clean and presented no evidence of an overflow issue. Geo did not give any fault codes indicating that there was a drain issue. Thermostat is giving a false alarm and recommended replacing. Changed thermostat and verified it was working in heating and cooling. Verified that heat strips were energizing. Cleaned overflow sensor in condensate pan.

Got to system and blower was running and outdoor unit was running and at this time could not find issue weather it’s a broad or blower will need to have him call again when issue is happening called for a 21 sh and had a 20 sh filter clean and coils clean

Drain was backed up on geo System and unclogged drain and tested 52° supply and 74° return and filter was clean and also added drain pan treatment for drain clogs in future. Watch unit run for 15 mins and got down 2 degrees in home and also gave estimates on I wave and duct cleaning

Remove and clean blower

Replaced control board for furnace. Verified operation.

Customer had stated that the blower for the furnace constantly runs even when ac is not running. When I got into attic I found that blower was in fact running even when there is no call but I also found that the draft fan was also randomly turning on and off. After some testing I’ve confirmed that the control board is bad and needs changed out. Office to confirm price of board

When I got to the job I found the filter to be heavily plugged up. The furnace was also not getting any power to the board, after some testing I found the transformer to be burnt out. After changing it everything started up and I ran tests on the system to ensure proper operation

Performed precision tuneup on ac, everything looks good. Customer stated that her uv light wasn’t working. After taking unit apart and testing voltages I found that the transformer suppling power to the unit was not working, I changed it out and tested light and it is working properly now, customer also mentioned that sometime after the winter heating tuneup she had water on her floor from the humidifier. When I took it apart I found the drain to be plugged from the pad having so much junk on it, I took the pad out and washed it and the case it’s kept in was washed as well. Due to the pad having so much junk on it I believe it was not properly checked during her heating tuneup so we will not charge her for cleaning it now

Repaired exposed wires in Carrier 38CKC036340 condenser unit damaged by rodent activity. Inspected entire wiring harness using Klein Tools ET310 electrical tester. Identified chewed sections of compressor and fan motor leads. Cut away damaged portions with Klein 11055 wire stripper. Spliced in new 14 AWG THHN wire using Ideal 30-1665 wire connectors. Applied 3M Super 33+ electrical tape for insulation. Sealed entry points with DAP 18351 expanding foam. Used CRC 02016 Rodent Repellent spray on wiring. Tested system operation with Fluke 116 HVAC multimeter. Completed repair in 1.5 hours, restoring proper functionality.

Found outdoor capacitor had failed on compressor side. Capacitor was replaced and I ensured system was operating properly. Customer purchased gold plan program.office to call and schedule routine maintenance.

Found outdoor capacitor had failed on the fan sid and tripped pressure switch. Changed capacitor and ensured proper operation of system.

Small turbo, capacitor. Perform precision AC tuneup after replacing small turbo capacitor unit is in good working condition filter size 16 x 25 x 1 . Two of them.

Flushed water heater. It did not fix issue, we will have to order a new neutralizer

Installed a new shower valve, ensuring all connections were secure and up to code. Used a pressure gauge to test for leaks and verified proper water flow and temperature control. The new valve operates smoothly, providing reliable performance. Regular maintenance is advised to ensure longevity and prevent future issues.

Unit wasn’t running. I found a low voltage wire to be disconnected, when I reconnected it the unit turned on. After I got the unit running the pressures were way too high, the unit was very dirty so washed it. I also found that the blower speeds weren’t properly set following furnace install so I set the correct blower speed for the ac. Filter was also very dirty and needed changed

They are having electrical work done and I found that the way it was hooked into the breaker box temporarily had an improper flow of electricity to the unit causing it to break down and not run. Will need a new unit

Found bad capacitor and disconnect box. Replaced both and verified proper operation.

Nothing wrong with ac unit. Customer wasn’t operating thermostat correctly and unknowingly set it too high

Removed and cleaned blower wheel. Reinstalled blower wheel, blower motor into housing. Reinstalled blower assembly back into air handler.

Checked unit and found that reversing valve a sticking we exercised the reversing valve and got it free up. We then found that the filter inside the air handler was extremely dirty. We also found that unit was 2 pounds low on 14 we found no signs of leaks. System has never been topped off with Freon before so we are going to watch it and see how it does over the next year or so system is now operating properly.