Plumbing & HVAC Services Edon OH

Estimate is for installing new 60,000 BTU 92% single stage furnace

Found inducer motor was clogged drain for furnace was clogged exhaust piping was clogged outside pressure switch port on the positive side was clogged. Flame sensor was dirty and needed to replace new filter. Also need to come back too fix exhaust pipe that is cracked from me taking it apart too be cleared and extended and also found fresh air and exhaust were mixing and fixed. Accidentally hit paycheck twice

I performed a heat tune-up on a gas furnace in Edon, OH, and found a weak capacitor. To ensure optimal performance, I replaced the weak capacitor with a 7.5mfd turbo capacitor. After completing the replacement, I verified the proper operation of the furnace, ensuring it is running efficiently and ready for the heating season. The system is functioning well with no further issues detected during the tune-up.

Performed gas leak search. Tested all fittings and regulator. Found a very slight leak at flex connection at stove. Replaced and leak checked. Relit pilot for water heater.

Installing whole home shut off in mechanical room.

Adjusted the float mechanisms in the toilets and removed gray sludge buildup from the floats. No parts required replacement; however, the poor water quality is contributing to the buildup. Advised the homeowner on potential water treatment options to address the issue and prevent future problems with the toilet components.

Replaced new shut offs on kitchen faucet checked for leaks no leaks, customer also signed up for a maintenance agreement

Quote for 13 seer 2.5 ton AC system and 60k btu 2 stage furnace

T1 pro thermostat. Perform precision AC tuneup. Upon inspection I noticed the thermostat was old and needed replaced temperature controls no longer worked. Replaced with T1 pro thermostat.

Found airflow blocked off at returns. Found dampers closed in basement. Unit has 10 degree superheat, 80 and 224 psi. Removed obstruction and ac ran good. Condenser needs a bath.

For this job, the customer said there furnace would light up, but the blower failed to come on. When arriving there, I turned the furnace on to find the burners lit up, but I checked for voltage going to the blower motor and got good readings, but it would not come on. So after informing the customer, what I found, I recommended replacing the blower motor. Both part and labor is still under warranty. The customer gave me the OK to have that part ordered And I also recommended to the customer getting a maintenance plan with us and they’d sign up for that. The customer does have temporary electric heat And as of right now, the furnace is not in working condition.

Pulling both stools and resetting on new flanges. Cutting out and removing all cast under the floor. Cutting off and reattaching to vents and any drains that have a p-trap. Replacing any plumbing that has S-traps.

The evaporator coil is leaking at a decent rate. Customer wanted us to charge system a little so they have time to think about what system they want to put in whether it’s a furnace and AC set up or a new geothermal.

Replacing all accessible cast under the floor. up to 60' of 3" PVC and misc fittings. up to 40' of 2" PVC and misc fittings. up to 30' of 1.5 PVC and misc fittings. this includes discarding all old plumbing.

For this job, the customer was having problems her toilet and shower not draining properly. Confirming that it was not a vent issue, we pulled the toilet out and ran the camera into the drain and found the blockage. We also noticed the main Drain had fingers inside. Running the drain machine, we was able to break loose the blockage. Setting the toilet back in place we ran the water and did not have any backfill. Also, recommend getting new drain system, the drain is an old galvanized system. Customer want us to give her a quote and give her a call As of right now, we did not find any any other issues with the toilet.

I traced out circuit in hallway and found that there was A bad outlet that was causing the other four hallway outlets to have issues, I replaced the outlet with one I had on my truck and verified there was power at all five outlets. However, I did notice that all the outlets in series were old and had signs of heat discoloration. I recommended replacing them, and customer is going to replace herself.

Replacing OSB underwater heater. Cutting out bad fitting for toilet and replacing it Replacing OSB underwater heater. Replacing fitting and section of pipe underneath the toilet that was disconnected from the toilet

For this job, I performed maintenance on the furnace. After checking everything, I did not find any issues with the system. The filter has gotten changed The filter size is 16 x 25 x 5 Goodman I did notice the gasket around the collector box was wearing out and it did show signs of water damage. Showing the customer the pictures that I took, I recommended to them getting a new seal for the collector box With the customers permission, I removed the old seal And replaced it with a high temp sealant. After I reinstalled the collector box and the inducer motor, I checked the operation of the furnace and did not find any issues with the system The system is in normal condition

Ran a dedicated circuit to sump pump, isolated bedroom to its own circuit and repaired a broken waterline under the kitchen sink installed two new stops and supply lines. Ran out of time to trace out power in hallway we need to return to do that.

Found system needs flushed and possibly a new flow valve. Will return to flush system tomorrow. Tech support was contacted and advised same. Gold plan purchased.

Found flame sensor was not reading flame (reading .1 ua) Removed and cleaned. Verified sensor was reading 2.4 ua. Furnace is now working properly. I did recommend gold plan membership for preventative maintenance. I also recommend new burners and a blower wheel cleaning.

Rebuilt one toilet and replaced flapper on the other. Verified proper operation.

Reconnected vent pipe properly and cleared debris out of it.

Installed air handler and AC ensured proper operation.

Found trap to be plugged. Removed trap and cleaned it out then reinstalled so that it can be serviced in the future